Quantcast
TRENCHER ATTACHMENTS 1654 PARTS PAGE-NEW
END & IDLER SPROCKET
ROLLERS



DIGGING TEETH
          CUP TEETH

136024     CUP TOOTH L/H     $5.00                                                  136025     CUP TOOTH R/H     $5.00
CARBIDE CUTTERS
BULLET BIT TYPE        $17.50

CSM1654C  BULLET BIT HOLDER CENTER  

CSM1654R   BULLET BIT HOLDER R/H   

CSM1654L   BULLET BIT HOLDER L/H   


CC-1    CARBIDE BULLET BIT        $5.75


CARBIDE CUTTERS
SHARK TOOTH TYPE

                                        $17.50                                                                                                        

SSM1654C    SHARK SIDEMOUNT CENTER          

SSM1654R    SHARK SIDEMOUNT R/H        

SSM1654L    SHARK SIDEMOUNTL/H          
CC-1  BIT 
NOT INCLUDED

FIND
DRIVE SPROCKETS

NONE AVAILABLE AT THIS TIME
NONE AVAILABLE AT THIS TIME
NONE AVAILABLE AT THIS TIME

Buy this

ATTACHMENTS
Using 1.654" Pitch Chain
Freight Special $35.00 on On line Orders (Limited to the continental U.S.)
Models #  BOBCAT,  BRADCO, LOWE, TINK
email me
TRENCHER DIGGING PARTS FOR 
REPLACEMENT DIGGING PARTS LLC
       CHAIN REPAIR PARTS
CHRL1654    REPAIR LINK (INC 2 PINS)                                                                                                 
                        FOR THE 2 PITCH CHAIN                         
                                                                          $20.50                                   CHAIN PIN (WITH KEY)                                             ROLLER LINK  1.5" WIDE                                                    IMPORTANT  NOTICE                                                                  137001                                                      $10.50                                                             ROLLER LINK ON REPAIR LINK IS  1.5" WIDE                                              $3.50                                   IMPORTANT  NOTICE 
                                                                                                                                                                              ROLLER LINKS ON NEWER CHAINS ARE 1.5"WIDE                                                                                                                                                                                  ROLLER LINKS ON OLDER CHAINS ARE1 3/8" WIDE
1.654" PITCH     BARE DIGGING CHAIN & DIGGING CHAIN ASSEMBLIES
                                      (PITCH IS THE CENTER TO CENTER MEASUREMENT OF THE CHAIN PINS)
                                    (NUMBER OF LINKS ON A CHAIN IS THE NUMBER OF CHAIN PINS DIVIDED BY 2)

































































             



If you have questions
 call 1-800-4471941 or
 Email us
 bill@replacementdiggingparts.com
Fax 877-255-7781
The welded Shark Tooth Chain is a maintenance free low profile chain assembly. The carbide tipped shark tooth will out last the chain. Tension Adjustment is the only maintenance required.  A great chain for digging hard rock, caliche, coral, and limestone 
Lowest Cost trencher chain.  Use in the easiest of digging conditions such as  sand, sandy loam, loose shale, loose soil and sticky clay of dirt.

Low cost trencher chain.  Best for trenching sand, sandy loam, loose shale, loose soil, caliche and clay.
This 50/50 chain configuration allows for trenching in almost any type of ground.  The carbide tipped replaceable Bullet Bits are bolted to the chain and used to break up the ground. The cup teeth follow to clean the trench.  Use on loose dirt, medium and hard rocky soil.
This 50/50 chain configuration allows for trenching in almost any type of ground also.  The non-replaceable Shark Tooth will out last the chain. The Cup Teeth follow  the Shark Teeth to clean the trench.  Use on loose dirt, medium and hard rocky soil.
The bolt-on rock and frost chain is used on hard rocky conditions and frozen ground.This chain uses replaceable carbide tipped bullet bits to pick and fracture hard rock and frozen ground. 
CALL
 800-447-1941

  TO OBTAIN CURRENT PRICING ON DIGGING CHAIN
CALL
 800-447-1941
  TO OBTAIN CURRENT PRICING ON DIGGING CHAIN
4 PITCH SPACING CUP TOOTH CHAIN   4" CUT
4 PITCH SPACING BARE CHAIN
​2 PITCH SPACING BARE CHAIN
2 PITCH SPACING CUP TOOTH CHAIN   4" CUT
2 PITCH 50/50 COMBO CHAIN 4" CUT
(CARBIDE TIPPED BULLET BIT & CUP TOOTH)

2 PITCH 50/50 COMBO SHARK CHAIN  4"CUT
(CARBIDE FACED SHARK TOOTH & CUP TOOTH) 
​2 PITCH ALL BOLT-ON BULLET BIT CHAIN 4" CUT
WELDED LOW PROFILE SHARK CHAIN  4" CUT
THIS IS OUR BEST SELLING CHAIN