BULLET BIT HOLDERS
$31.25
136036 BULLET BIT HOLDER
4" CUT R/H
136037 BULLET BIT HOLDER
4" CUT L/H
136038 BULLET BIT HOLDER
5" CUT R/H
136039 BULLET BIT HOLDER
5" CUT L/H
136040 BULLET BIT HOLDER
6" CUT R/H
136041 BULLET BIT HOLDER
6" CUT L/H
note: bullet bits not included with holders
CARBIDE BULLET BITS
765CBFP CARBIDE BULLET BIT $9.95
W/ FLARED POCKET PROTECTOR
765CRFM CARBIDE BULLET BIT W/ FLARED
& C CLIP $9.95
TRENCHER ATTACHMENTS USING 2.00" PITCH CHAIN
SHARK CARBIDE CUTTERS
$33.20
136236 SHARK SIDEMOUNT CENTER
4" CUT R/H
136237 SHARK SIDEMOUNT CENTER
4" CUT L/H
136238 SHARK SIDEMOUNT CENTER
5" CUT R/H
136239 SHARK SIDEMOUNT CENTER
5" CUT L/H
136240 SHARK SIDEMOUNT CENTER
6" CUT R/H
136241 SHARK SIDEMOUNT CENTER
6" CUT L/H
CHAIN REPAIR PARTS
CHRL200 REPAIR LINK (INC 2 PINS)
$28.10 FOR THE 2 PITCH CHAIN 137202H CONNECTOR LINK
$15.30
137203 ROLLER LINK 135351 $4.95 CHAIN PIN (WITH KEY)
Fax 877-255-7781
BARE CHAIN & DIGGING CHAIN ASSEMBLIES
The Welded Shark Tooth Chain is a MAINTENANCE FREE low profile chain assembly.
The CARBIDE TIPPED shark tooth will OUTLAST THE CHAIN. Tension Adjustment is the only maintenance required. A great chain for digging HARD ROCK, CALICHE, CORAL, AND LIMESTONE. THIS IS A GOOD CHAIN FOR TREE ROOTS.
LOWEST PRICED standard trencher chain is use in the easiest of digging conditions,
such as:
SAND, SANDY LOAM, LOOSE SHALE, LOOSE SOIL AND STICKY CLAY.
LOWEST double standard chain. Best for trenching SAND, SANDY LOAM, LOOSE SOIL, LOOSE SHALE, CALICHE, AND CLAY.
This 50/50 chain configuration allows for trenching in almost any type of ground.
The CARBIDE TIP replaceable BULLET BITS are bolted to the chain and used to break up the ground. The cup teeth follow to clean the trench. This 50/50 double standard chain will give the highest production in FROZEN GROUND, HIGHLY COMPACTED SOILS AND ROCK.
This 50/50 double standard chain configuration allows for trenching in almost any type of ground. The non-replaceable SHARK TOOTH will OUTLAST the chain. The Teeth follow the CARBIDE TOOTH to clean the trench. This is a double standard chain Used on FROZEN GROUND, HIGHLY COMPACTED SOILS AND ROCK.
The Bolt-on Rock and Frost Chain are used on HARD ROCKY CONDITIONS AND FROZEN GROUND. This double standard chain uses REPLACABLE BULLET BITS to PICK AND FRACTURE ROCK AND HARD GROUND.
CALL
800-447-1941
TO OBTAIN CURRENT PRICING ON DIGGING CHAIN
CUP TEETH
DOUBLE HARDFACED
(1/2" bolts, 2" on center)
135924 CUP TOOTH L/H $6.44
135925 CUP TOOTH R/H $6.44
QUICK
FIND
REPAIR PARTS FOR CARBIDE CUTTERS
765HDBLK BULLET BIT POCKET $13.95
SH2.0 SHARK CUTTER $17.95
Do you need a chain for trenching in extreme conditions? Use this chain in HARD ROCKY CONDITIONS, FROZEN GROUND, ASPHALT, CONCRETE AND LIMESTONE. The welded H-plate chain gives you the best bit penetration angle. This assembly has HEAVY-DUTY, HEAT-TREATED POCKETS, AND ROCK BITS WITH POCKET PROTECTORS.
ATTACHMENTS
Using 2.00" Pitch Chain
Models # BOBCAT, BRADCO, CATERPILLER, LOWE, TINK
TRENCHER DIGGING PARTS FOR
REPLACEMENT DIGGING PARTS LLC
800-447-1941
$23.99
| ||||||
FREIGHT ONLY $35.00
ANYTHING UP TO
60LBS.
(LIMITED TO THE U.S. ONLY)
| ||||||
4 PITCH SPACING - 2" PITCH CUP TOOTH CHAIN
2" PITCH BARE CHAIN
2" PITCH CUP TOOTH CHAIN 6" CUT.
2" PITCH 50/50 COMBO CHAIN 6" CUT
(CARBIDE TIPPED BULLET BITS & CUP TEETH)
2" PITCH 50/50 COMBO CHAIN 6" CUT
(CARBIDE TIPPED SHARK TEETH & CUP TOOTH
2" PITCH CARBIDE TIPPED SHARK TOOTH CHAIN 6" CUT
2" PITCH ALL ROCK & FROST CHAIN 6" CUT
(CARBIDE TIPPED BULLET BITS)
2" PITCH ALL BULLET H-PLATE CHAIN 6" CUT
THIS IS OUR BEST-SELLING CHAIN.
*BOLTED CHAINS ALLOW FOR WIDER CUTS
