CARBIDE CUTTERS WELDED SHARK STYLE. $18.95 BUY ONCE PER CHAIN
SSM1654C SHARK SIDEMOUNT CENTER
SSM1654R SHARK SIDEMOUNT R/H
SSM1654L SHARK SIDEMOUNTL/H
*The Shark Style Will Outlast a Chain
PARTS FOR BOBCAT, BURKEEN & MIDMARK TRENCHERS USING 1.654" CHAIN
END & IDLER SPROCKET
503664 SPROCKET ASSEMBY
10 TOOTH $82.65
125009 1 1/8 SQ. HOLE BEARING $35.25
115464 SNAP RING $2.98
232645 IDLER SHAFT SQ. $10.51
ROLLERS AND BEARING
(NOT AVAILABLE AT THIS TIME)
6576140 1" SQ. HOLE BEARING
$65.00
CARBIDE CUTTERS BULLET BIT TYPE $18.95
CSM1654C BULLET BIT HOLDER CENTER
CSM1654R BULLET BIT HOLDER R/H
CSM1654L BULLET BIT HOLDER L/H
CC-1 CARBIDE BULLET BIT $6.95
SHANK IS 0.55
CC-1 BIT
NOT INCLUDED WITH HOLDERS
CHAIN REPAIR PARTS
CHRL1650 REPAIR LINK (INC 2 PINS) CHRL1640 REPAIR LINK (INC 2 PINS)
FOR THE 2 PITCH CHAIN FOR THE 4 PITCH CHAIN
$20.75 $20.67
137003 ROLLER LINK (1.50" WIDE) 137001 CHAIN PIN (WITH KEY) 137002H CONNECTOR LINK $3.50
$10.50
$15.50
CUP TEETH
136024 CUP TOOTH L/H $5.86 136025 CUP TOOTH R/H $5.86
BOBCAT, MIDMARK, BURKEEN
Using 1.654" Pitch Chain
TRENCHER DIGGING PARTS FOR
REPLACEMENT DIGGING PARTS LLC
ATTENTION
FOR BOBCAT TRENCHER ATTACHMENTS SELECT BOBCAT IN THE ATTACHMENT BOX ON THE HOME PAGE
1.654" PITCH BARE DIGGING CHAIN & DIGGING CHAIN ASSEMBLIES
(PITCH IS THE CENTER TO CENTER MEASUREMENT OF THE CHAIN PINS)
(NUMBER OF LINKS ON A CHAIN IS THE NUMBER OF CHAIN PINS DIVIDED BY 2)
If you have questions
call 1-800-4471941 or
Email
The welded Shark Tooth Chain is a maintenance free low profile chain assembly. The carbide tipped shark tooth will outlast the chain. Tension Adjustment is the only maintenance required. A great chain for digging, HARD ROCK, CALICHE, CORAL, and LIMESTONE.
Lowest Cost trencher chain. Use in the easiest of digging conditions such as SAND, SANDY LOAM, LOOSE SHALE, LOOSE SOIL and STICKY CLAY.
Low-cost trencher chain. Best for trenching SANDY, SANDY LOAM, LOOSE SHALE, LOOSE SOIL, CALICHE and CLAY.
This 50/50 chain configuration allows for trenching in almost any type of ground. The carbide tipped replaceable Bullet Bits are bolted to the chain and used to break up the ground. The cup teeth follow to clean the trench. Use on LOOSE DIRT, MEDIUM and HARD ROCKY SOIL.
This 50/50 chain configuration allows for trenching in almost any type of ground. The non-replaceable Shark Tooth will outlast the chain. The Cup Teeth follow the Shark Teeth to clean the trench. Use on LOOSE DIRT, MEDIUM and HARD ROCKY SOIL.
The bolt-on rock and frost chain are used on HARD ROCKY CONDITIONS and FROZEN GROUND. This chain uses replaceable carbide tipped bullet bits to pick and fracture hard rock and frozen ground.
CALL
800-447-1941
TO OBTAIN CURRENT PRICING ON DIGGING CHAIN
4 PITCH SPACING 1.654" PITCH CUP TOOTH CHAIN 4" CUT
1.654" PITCH CUP TOOTH CHAIN 4" CUT
1.654" PITCH 50/50 COMBO CHAIN 4" CUT
(CARBIDE TIPPED BULLET BIT & CUP TOOTH)
1.654" PITCH 50/50 COMBO SHARK CHAIN 4"CUT
(CARBIDE FACED SHARK TOOTH & CUP TOOTH)
1.654" PITCH ALL BOLT-ON BULLET BIT CHAIN 4" CUT
1.654" PITCH WELDED LOW PROFILE SHARK CHAIN 4" CUT
THIS IS OUR BEST SELLING CHAIN
CALL
800-447-1941
TO OBTAIN CURRENT PRICING ON DIGGING CHAIN
*BOLTED CHAINS ALLOW FOR WIDER CUTS
FREIGHT ONLY $35.00
ANYTHING UP TO
60LBS..
(LIMITED TO THE U.S. ONLY)