CUP CUTTERS
(5/8" bolts, 2" on centers )
188744A1 CUP TOOTH R/H $8.64
188746A1 CUP TOOTH L/H $8.64
CHAIN REPAIR PARTS
CHRL2609 REPAIR LINK (INC 2 PINS)
FOR THE 2.609 PITCH CHAIN 2609RL ROLLER LINK
$20.78
$29.98
$5.95
2609CP CHAIN PIN (WITH KEY)
2.609" PITCH BARE DIGGING CHAIN & DIGGING CHAIN ASSEMBLIES
(PITCH IS THE CENTER TO CENTER MESURMENT OF THE CHAIN PINS)
(NUMBER OF LINKS ON A CHAIN IS THE NUMBER OF CHAIN PINS DIVIDED BY 2)
DRIVE SPROCKETS
148569 SPLIT 9 TOOTH $99.00
(25+4XP, 30+4, 40+4, 360,
TF600 & 700, DH4 & 5)
122432A1 SPLIT 14 TOOTH $584.78
(460, 560, RT460, RT560)
104152A1
SPLIT 15 TOOTH $365.00

(460, 560, RT460, RT560)
AUGER DRIVE SPROCKETS
126170A AUGER DR. SPK 14T (2.189"bore) $250.00
126172A AUGER DR. SPK 14T (2.000"bore) $250.00
ROLLERS
531384 END ROLLER ASSEMBLY $179.80
(1.5" sq. ID)
747444 SQ. HOLE BEARING FOR 531384 $56.00
(1.5" sq. ID)
675070A END ROLLER ASSEMBLY 14.25" $798.23
(includes tapered roller bearings, cups, spacers, seals and dust washers).
759118KIT BEARING KIT (for 675070 Roller) $290.00
(includes tapered roller bearings, cups)
CALL FOR INFO ON 20" ROLLER
438570 GREASABLE IDLER SHAFT FOR 675070AKIT
$99.00
IDLER SPROCKETS
531251 IDLER SPROCKET ASSEMBLY
(1 1/8" sq. ID) $137.60
125009 SQ. HOLE BEARING FOR 125009
(1 1/8" sq. ID) $35.25
251033 SQ. SHAFT FOR IDLER SPROCKET
(1.125" X 2.25") $47.00
2.609" PITCH ALL BULLET H-PLATE CHAIN 6" CUT
SHARK TOOTH CARBIDE CUTTERS
$31.35
23658 SHARK SIDEMOUNT CENTER
4" CUT R/H
23758 SHARK SIDEMOUNT CENTER
4" CUT L/H
23958 SHARK SIDEMOUNT CENTER
5" CUT R/H
23858 SHARK SIDEMOUNT CENTER
5" CUT L/H
24058 SHARK SIDEMOUNT CENTER
6" CUT R/H
24158 SHARK SIDEMOUNT CENTER
6" CUT L/H
REPAIR PARTS FOR CARBIDE CUTTERS
765HDBLK BULLET BIT POCKET $13.95
SH2.0 SHARK CUTTER $17.95
BULLET BIT HOLDERS
$33.50
CARBIDE BULLET BITS Bullets not included with side mounts
765CBFP CARBIDE BULLET BIT $10.95
W/ FLARED POCKET PROTECTOR
765CRFN CARBIDE BULLET BIT W/ FLARED
& C CLIP $10.95
03658 BULLET BIT HOLDER
4" CUT R/H $33.50
03758 BULLET BIT HOLDER
4" CUT L/H $33.50
03858 BULLET BIT HOLDER
5" CUT R/H $33.50
03958 BULLET BIT HOLDER
5" CUT L/H $33.50
04058 BULLET BIT HOLDER
6" CUT R/H $33.50
04158 BULLET BIT HOLDER
6" CUT L/H $33.50
CASE, DAVIS, ASTEC, TORO
Using 2.609" Pitch Chain, 50,000LB.
TRENCHER DIGGING PARTS FOR
REPLACEMENT DIGGING PARTS LLC
Models # 25+4 XP, 30+4, 40+4, 70+4, RT360, 460, 560, DH4, DH5, TF600
If you have questions
call 1-800-4471941 or Email
The Welded Shark Tooth Chain is a maintenance free low profile chain assembly. The carbide tipped shark tooth will outlast the chain. Tension Adjustment is the only maintenance required. A great chain for digging HARD ROCK, CALICHE, CORAL AND LIMESTONE.
Low-cost trencher chain. Best for trenching SAND, SANDY LOAM, LOOSE SHALE, LOOSE SOIL, CALICHE AND CLAY.
This 50/50 chain configuration allows for trenching in almost any type of ground. The carbide tipped replaceable bullet bits are bolted to the chain and used to break up the ground. The cup teeth follow to clean the trench. Use on LOOSE DIRT, MEDIUM AND HARD ROCKY SOIL.
This 50/50 chain configuration allows for trenching in almost any type of ground. The non-replaceable Shark Tooth will outlast the chain. The cup teeth follow the Shark Tooth to clean the trench. Use on LOOSE DIRT, MEDIUM AND HARD ROCKY SOIL.
The bolt-on rock and frost chain are used on HARD ROCKY CONDITIONS AND FROZEN GROUND. This chain uses replaceable carbide tipped bullet bits to pick and fracture hard rock and frozen ground.
CALL
800-447-1941
TO OBTAIN CURRENT PRICING ON DIGGING CHAIN
CALL
800-447-1941
TO OBTAIN CURRENT PRICING ON DIGGING CHAIN
Do you need a chain for trenching in extreme conditions? USE THIS CHAIN IN HARD ROCKY CONDITIONS, FROZEN GROUND, ASPHALT AND CONCRETE. The welded H-plate chain gives you the best bit penetration angle plus great trench clean out. This assembly has heavy-duty, heat-treated pockets and rock bits with pocket protectors.
2.609" PITCH WELDED SHARK TOOTH CHAIN
2.609" PITCH ALL CUP TOOTH CHAIN
2.609" PITCH 50/50 COMBO CHAIN (BULLET AND CUP TOOTH)
2.609" PITCH 50/50 COMBO CHAIN. (SHARK AND CUP TOOTH)
2.609" PITCH ALL CARBIDE BULLET BITS.
THIS IS OUR BEST SELLING CHAIN.
* BOLTED CHAINS ALLOW FOR WIDER CUTS.
FREIGHT ONLY $35.00
ANYTHING UP TO
60LBS.
(LIMITED TO THE U.S. ONLY)