BULLET BIT HOLDERS
$31.25
136036 BULLET BIT HOLDER
4" CUT R/H
136037 BULLET BIT HOLDER
4" CUT L/H
136038 BULLET BIT HOLDER
5" CUT R/H
136039 BULLET BIT HOLDER
5" CUT L/H
136040 BULLET BIT HOLDER
6" CUT R/H
136041 BULLET BIT HOLDER
6" CUT L/H
note: bullet bits not included with holders
CARBIDE BULLET BITS
765CBFP CARBIDE BULLET BIT $10.95
W/ FLARED POCKET PROTECTOR
765CRFN CARBIDE BULLET BIT W/ FLARED
& C CLIP $10.95
VERMEER TRENCHERS USING 2.00"PITCH (2481M or 2960) CHAIN
SHARK CARBIDE CUTTERS
$33.20
136236 SHARK SIDEMOUNT CENTER
4" CUT R/H
136237 SHARK SIDEMOUNT CENTER
4" CUT L/H
136238 SHARK SIDEMOUNT CENTER
5" CUT R/H
136239 SHARK SIDEMOUNT CENTER
5" CUT L/H
136240 SHARK SIDEMOUNT CENTER
6" CUT R/H
136241 SHARK SIDEMOUNT CENTER
6" CUT L/H
CHAIN REPAIR PARTS
CHRL200 REPAIR LINK (INC 2 PINS)
$33.23 FOR THE 2 PITCH CHAIN 137202H $ 25.10 CONNECTOR LINK
$15.30
137203 ROLLER LINK 135351 $4.10 CHAIN PIN (WITH KEY)
Fax 877-255-7781
BARE CHAIN & DIGGING CHAIN ASSEMBLIES
The welded Shark Tooth Chain is a maintenance free low profile chain assembly. The carbide tipped shark tooth will outlast the chain. Tension Adjustment is the only maintenance required. A great chain for digging HARD ROCK, CALICHE, CORAL, AND LIMESTONE.
Lowest Cost trencher chain. Use in the easiest of digging conditions such as SAND, SANDY LOAM, LOOSE SHALE, LOOSE SOIL, AND STICKY CLAY,
High Quality Anti back flex chain. Best for trenching SAND, SANDY LOAM, LOOSE SHALE, LOOSE SOIL, CALICHE, AND CLAY.
This 50/50 chain configuration allows for trenching in almost any type of ground. The carbide tipped replaceable bullet bits are bolted to the chain and used to break up the ground. The cup teeth follow to clean the trench. Use on LOOSE DIRT, MEDIUM, AND HARD ROCKY SOIL.
This 50/50 chain configuration allows for trenching in almost any type of ground. The non-replaceable Shark Tooth will outlast the chain. The cup teeth follow the Shark Tooth to clean the trench. Use on LOOSE DIRT, MEDIUM, AND HARD ROCKY SOIL.
The bolt-on rock and frost chain are used on HARD ROCKY CONDITIONS AND ROCKY GROUND. This chain uses replaceable carbide tipped bullet bits to pick and fracture hard rock and frozen ground.
CALL
800-447-1941
TO OBTAIN CURRENT PRICING ON DIGGING CHAIN
CALL
800-447-1941
TO OBTAIN CURRENT PRICING ON DIGGING CHAIN
CHAIN DRIVE SPROCKETS
203601001 SPLIT 12 TOOTH $177.50
(RT350)
716212 BOLTS 7/16X2.5" (6 REQ.) $2.25
716LN 7/16" LOCK NUT (6 REQ.) $0.95
210000001 SPLIT 15 TOOTH $217.80
(V4150, V5750, RT450, SO3550)
583 BOLT 5/8X3" (6 REQ.) $1.75
58LN 5/8" LOCK NUT (6 REQ.) $0.95
242742001 SOLID 15 TOOTH $262.80
(V3550, RT450 WITH LOW HEAD)
254147001 BOLT, M14-2.0X75mm (11 REQ,) $2.95
1647001 LOCK WASHER M14 (11 REQ.) $1.35
CUP TEETH
DOUBLE HARDFACED
(1/2" bolts, 2" on center)
135924 CUP TOOTH L/H $6.65
135925 CUP TOOTH R/H $6.65
QUICK
FIND
REPAIR PARTS FOR CARBIDE CUTTERS
765HDBLK BULLET BIT POCKET $13.95
SH2.0 SHARK CUTTER $17.95
ROLLERS & AUGER SPROCKETS
252665003 15" BOOM END ROLLER ASSEMBLY $610.25
(INCLUDES BEARING CUP, CONE, SEAL & SLEEVE)
252602003 8.5" BOOM END ROLLER ASSEMBLY $525.30
(INCLUDES BEARING CUP, CONE, SEAL & SLEEVE)
1715023 BEARING CUP FOR ROLLERS (2 REQUIRED) $21.33
1716023 BEARING CONE FOR ROLLERS (2 REQUIRED) $46.24
252655001 SEAL FOR ROLLERS (2 REQUIRED) $ 16.21
252663001 SEAL SLEEVE FOR ROLLERS (2 REQUIRED) $33.36
40070001 GREASE BOLT WITH ZERK FOR ROLLERS $86.80
248692001 AUGER SPROCKET WITH SHAFT $299.98
220700003 PILLOW BLOCK BEARING FOR AUGER (2 REQ.) $80.30
1709007 ROUND FLANGE BEARING FOR AUGER (2 REQ.) $125.56
Do you need a chain for trenching in extreme conditions? Use this chain in HARD ROCKY CONDITIONS, FROZEN GROUND, ASPHALT, AND CONCRETE. The welded H-plate chain gives you the best bit penetration angle plus great trench clean out. This assembly has heavy-duty, heat-treated pockets and rock bits with pocket protectors.
VERMEERR
Using 2.00" Pitch Chain
TRENCHER DIGGING PARTS FOR
REPLACEMENT DIGGING PARTS LLC
800-447-1941
| ||||||
4 PITCH SPACING - 2" PITCH CUP TOOTH CHAIN 6" CUT
2" PITCH BARE CHAIN
2" PITCH CUP TOOTH CHAIN 6" CUT
*BOLTED CHAINS ALLOW FOR A WIDER TRENCH
2" PITCH 50/50 COMBO CHAIN 6" CUT
(CARBIDE TIPPED BULLET BITS & CUP TOOTH)
THIS IS OUR BEST-SELLING CHAIN
2" PITCH 50/50 COMBO CHAIN 6" CUT
(CARBIDE TIPPED SHARK TEETH & CUP TOOTH)
2" PITCH SHARK TOOTH WELDED CHAIN 6" CUT
2" PITCH ALL ROCK & FROST CHAIN 6" CUT
(CARBIDE TIPPED BULLET BITS)
2" PITCH ALL BULLET H-PLATE CHAIN 6" CUT
FREIGHT ONLY $35.00
UP TO 60LBS.
ONLINE ONLY
| ||||||
