TORO-DINGO1654PARTS

ROLLER & BEARINGS

1079325 6-3/4" ROLLER ASSEMBLY $181.50

1041995 BEARING SQ. HOLE 1 1/8" $45.20

CARBIDE CUTTERS

BULLET BIT TYPE $18.95

CSM1654C BULLET BIT HOLDER CENTER

CSM1654R BULLET BIT HOLDER R/H

CSM1654L BULLET BIT HOLDER L/H

CC-1 CARBIDE BULLET BIT $6.95

CARBIDE CUTTERS

SHARK TOOTH TYPE

$18.95

SSM1654C SHARK SIDEMOUNT CENTER

SSM1654R SHARK SIDEMOUNT R/H

SSM1654L SHARK SIDEMOUNTL/H

CHAIN REPAIR PARTS

CHRL1654 REPAIR LINK (INC 2 PINS) CHRL1640 REPAIR LINK (INC 2 PINS)

$20.75 FOR THE 2 PITCH CHAIN $20.67 FOR THE 4 PITCH CHAIN

$3.50 $ 15.50

$10.50

137003 ROLLER LINK 137001 CHAIN PIN (WITH KEY) CONNECTOR LINK 137002H

DRIVE SPROCKETS

1041964 SOLID 12 TOOTH $155.23

(6) 1/2" BOLT HOLES

FOR TRX MODELS

1001699 SOLID 12 TOOTH $145.00

(2) 3/8" BOLT HOLES

FOR TORO, DINGO MODELS

CUP TEETH

DOUBLE HARDFACED

(3/8" bolts, 1 1/8" TO1.8125 Slotted)

136024 CUP TOOTH L/H $5.86

136025 CUP TOOTH R/H $5.86

4 PITCH SPACING 1.654" CUP TOOTH CHAIN 4" CUT

1.654" PITCH BARE CHAIN

1.654" PITCH CUP TOOTH CHAIN 4" CUT

1.654" PITCH 50\50 COMBO CHAIN 4" CUT *BOLTED CHAINS ALLOW FOR A WIDER TRENCH

(CARBIDE TIPPED BULLET BITS & CUP TOOTH)

1.654" PITCH 50\50 COMBO CHAIN 4" CUT

(CARBIDE TIPPED SHARK TEETH & CUP TOOTH)

THIS IS OUR BEST-SELLING CHAIN

1.654" PITCH SHARK TOOTH WELDED CHAIN 4" CUT

1.654" PITCH ALL ROCK & FROST CHAIN 4" CUT

(CARBIDE TIPPED BULLET BITS)

The welded Shark Tooth Chain is a maintenance free low profile chain assembly. The carbide tipped shark tooth will outlast the chain. Tension Adjustment is the only maintenance required. A great chain for digging HARD ROCK, CALICHE, CORAL, AND LIMESTONE.

Lowest Cost trencher chain. Use in the easiest of digging conditions such as SAND, SANDY LOAM, LOOSE SHALE, LOOSE SOIL, AND STICKY CLAY.

Low-cost trencher chain. Best for trenching SANDM SANDY LOAM, LOOSE SHALE, LOOSE SOIL, CALICHE, AND CLAY.

This 50/50 chain configuration allows for trenching in almost any type of ground. The carbide tipped replaceable bullet bits are bolted to the chain and used to break up the ground. The cup teeth follow to clean the trench. Use on LOOSE DIRT, MEDIUM, AND HARD ROCKY CONDITIONS.

This 50/50 chain configuration allows for trenching in almost any type of ground. The non-replaceable Shark Tooth will outlast the chain. The cup teeth follow the Shark Tooth to clean the trench. Use on LOOSE DIRT, MEDIUM, AND HARD ROCKY SOIL.

The bolt-on rock and frost chain are used on HARD ROCKY CONDITIONS AND FROZEN GROUND. This chain uses replaceable carbide tipped bullet bits to pick and fracture hard rock and frozen ground.